Forum Post: RE: am335x-evm-05.07 - incorrect openssl hashes?
Hello,I have issues with openssl and the hardware crypto interface as well. My system is based on EZSDK 6.00.00.00. Try using openssl to open google's web site. With /dev/crypto present, I get...
View ArticleForum Post: RE: ubuntu on am335x
Hey,I got it booted up but I'm getting some errors and neither of the ethernet devices show up in ifconfig (just usb0 and lo). Any thoughts? I ran fsck on the two partitions and they're clean....
View ArticleForum Post: RE: beaglebone black to produce a PCM bus
Hi Nathan,Assuming that you are using linux, a good place to start would be the Sitara Linux SDK Audio page. The Audio DAC example would probably be of the most help to you, as it explains how to set...
View ArticleForum Post: about am335x debug info:[ 9934.190185] SR 1: curr=1162500,...
Hi, I am testing my board's HW and SW. But after the system run about 2 hours ,the kernel prints the debug info:[ 9934.190185] SR 1: curr=1162500, delta_v=-6664, calc=1155836, act=1162500, gain=22...
View ArticleForum Post: AM335x musb_hdrc_mod
Hello dear.I have found a problems. This problem was caused during file transfer using USB.So, I had to capture the log. ------------------------ System info...
View ArticleForum Post: GPMC 8bit AD muxed
In my system OMAP4 GPMC is comment to a FPGA in a 8 bit modeie AD0 ~ AD7, ALEn,WEn,OEn,CS2n. I have only this much connection to my FPGA(save my FPGA pin count). GPMC is configured asAsynchronous,...
View ArticleForum Post: ti81xx_interrupt 1119: CAUTION: musb0: Babble Interrupt Occured...
Hi, I am test my board with SW running. After the system run few hours , the kernel print errors continued:[23927.041320] ti81xx_interrupt 1119: CAUTION: musb0: Babble Interrupt...
View ArticleForum Post: RE: GPIO settings for AM335x
Hi Miroslav, I want to use GPIO2_3 as interrupt GPIO, Presently that GPIO is configured as Input pin on starter kit. when I am checking cat sys/kernel/debug/gpio. I am getting...
View ArticleForum Post: RE: beaglebone black to produce a PCM bus
no i don't know if the guide help out, i think i want to build as a module, not driver built into the Kernel.on...
View ArticleForum Post: Noob sdk7 opkg question
Hello,I am using sdk7 with linux 3.12 and the Beaglebone black. The rootfs seems to have a limited opkg as there is no gcc or python.Are there repositories for gcc, make and python for this 3.12...
View ArticleForum Post: RE: ubuntu on am335x
You can clean you 70-persistent-net.rules, to you ethx go correct...sudo echo "" > /etc/udev/rules.d/70-persistent-net.rulesshutdown -r now
View ArticleForum Post: AM3352 system with WL1271 Wifi only showing up as 80211.b
I have the WL1271 on my Sitara system setup in access point mode. However my Windows PC lists the network as only showing up in 80211.b mode. Why does it not show up as 80211n?
View ArticleForum Post: toggling a pin in AM3359 in the BBB
Out of curiosity, I would like to toggle a I/O pin in my BeagleBone Black (BBB) using a only C code. Yes, Similar to what we initially do when we get a new ARM-M development board.Now, I understand...
View ArticleForum Post: Burning AM3352 CPUs
Dear TI support ,We have an issue with burning AM3352 devices on SOM boards which we buy on the market.We thought that there might be an issue with the temprature grade of the CPU devices that are...
View ArticleForum Post: Where could i find "ts_calibrate" application?(EVM335x)
Hi, i'd like to use Touchscreen driver. i think this test application is included in the board.While i read http://processors.wiki.ti.com/index.php/AM335x_Touchscreen_Driver%27s_Guide,This mentioned...
View ArticleForum Post: RE: What happened to SmartReflex
Hi Matthew,I'll ask the factory team about this and will let you know when I have an answer.Best regards,Miroslav
View ArticleForum Post: RE: AM335x SD problem
I'm sorry, Steve, but nothing yet. I'll try to forward this again.Best regards,Miroslav
View ArticleForum Post: RE: GPIO settings for AM335x
Vishal,Please report the error code that request_irq() returns.Best regards,Miroslav
View ArticleForum Post: RE: USB powered Beaglebone Black
Do I understand correctly that this doesn't happen when the UART debug cable isn't plugged in?Best regards,Miroslav
View ArticleForum Post: RE: SD card initialization issue in Linux Kernel on customized board
Dear Miroslav,Thanks for your reply. I have checked the SD card, its working fine with my PC & AM335 starter kit with the same u-boot & Linux Image.Regards,Ankur
View Article