Forum Post: RE: About AM335x System Trace
Hi Biser,Thank you for the reply.Yes, I understood.Introduction Trace which I mentioned before uses this ETBand this Trace is the only method AM335x support currently.I will ask my local TI FAE when...
View ArticleForum Post: RE: AM335x enable usb gadget ethernet
No matter what host you use - Windows or Linux, you have to assign an IP address for the network interface of the board appeared on host. For example, on Linux the interface will be usb<X> as...
View ArticleForum Post: CCS Debug not possible when app code is running
Hi,I am using a custom board with Sitara AM3352.. The SPI EEPROm has the MLO and app file required for our application. The app files starts running as soon as I power up the board. In this case, I am...
View ArticleForum Post: RE: Noob sdk7 opkg question
Hi David,Yes, Yocto is an option as our SDK is Yocto compatible.Another option is to find an available and up-to-date package feed and add it to the opkg configuration. I'd suggest you look inside the...
View ArticleForum Post: RE: gcc cross-compile for am335x failes
Hi Miroslav,thank you so far, readelf tells me the requested interpreter is /lib/ld-linux-armhf.so.3, which my system lacks. So i guess i have the wrong rootfs installed (how do i find out which skd i...
View ArticleForum Post: RE: DDR3 Memory Support
Steve,Could you confirm part# of DDR3 RAM you are using for reference.Thanks,James
View ArticleForum Post: RE: SD card Interfacing with AM3352 processor.
MicroSD card has no card detect.In your linux board file, usestatic struct omap2_hsmmc_info am335x_mmc[] __initdata = {{ gpio_cd = -EINVAL; caps = MMC_CAP_4_BIT_DATA |...
View ArticleForum Post: RE: ti81xx_interrupt 1119: CAUTION: musb0: Babble Interrupt...
What is the test configuration? What's connected to the USB port in question?
View ArticleForum Post: RE: What sets USB DEV_CTL Host Mode bit 2?
Thilo,The reason is that only ONE usb port can be in host mode in u-boot.Here is the details: http://e2e.ti.com/support/arm/sitara_arm/f/791/p/345553/1208674.aspx#1208674
View ArticleForum Post: RE: NOR Boot of AM335x
Chandra,The below needs to be done by the assembly code to configure the upper address balls for MUX_MODE2 NOR flash boot.Configure ZCZ Ball Mode#...
View ArticleForum Post: RE: can we develop & debug Qt project in CCS
I would recommend looking at QT Creator for QT development. The following training link covers some basics on using QT creator:...
View ArticleForum Post: RE: Linux 3.12 on AM335x / Beaglebone
Franklin/Steve/Bin,I am using am335x-evm-sdk-src-07.00.00.00.tar.gz, board-support/linux-3.12.10-ti2013.12.01, when I use the following command to put processor into sleep mode,echo mem >...
View ArticleForum Post: RE: Networking Bug in SDK v07.00
Ok I've verified that this works. Might I suggest that you update the release notes to be a bit more clear that it not just a problem with DHCP and perhaps provided a link to the fix or at least post...
View ArticleForum Post: RE: dts ref doc
Normally you'd find the pinmux tables in the datasheet, but for some unknown reason it's missing from the am335x datasheet. Table 2-7 does list all relevant information for pinmuxing... except the...
View ArticleForum Post: pull up & pull down usage in TM4C123GXL
Hello everyone,I had some confusion on pull up & pull down configuration of board GPIO pinswhen i am doing pull up config in tm4c123gxl(in pull up mode- when switch is open - 3.3.v and switch is...
View ArticleForum Post: RE: AM335X: GPMC, DMA and NAND prefetch
Thank you for sharing with the community, Wolfgang!Best regards,Miroslav
View ArticleForum Post: RE: IO protection when interconnection an am335x with another...
TXS is a different family of devices from TXB and behavior is different.
View ArticleForum Post: RE: dts ref doc
Thanks Matthijs. I want to know one more thing, what is this sleep status in pin mux of am335x evm dts for some peripherals? should i have this in my dts?Regards,Gangadhar
View ArticleForum Post: RE: ti81xx_interrupt 1119: CAUTION: musb0: Babble Interrupt...
How to get the configuration?A USB sensor is connected to the USB port,I can read the sensor's data through USB port,thank you For your reply.
View Article