Forum Post: RE: AM6411: Schematic Review for OCP Timing Card Reference Design...
Hello Jennifer Thank you. Some changes have been made. going further, if a summary of the changes made is added, that would help. The off-page connections is expected to be a number. Can you please...
View ArticleForum Post: RE: AM62A7: AM62A7: When using export_op.py -c -m seg for model...
Hi Reese，thank you for your advice, now i update the tidl version to 10_01_03_00 and successfully complie the above two models to net.bin and io_1.bin,Then I cloned the edgeai_tidl_tool (10_01_03_00)...
View ArticleForum Post: RE: PROCESSOR-SDK-AM437X: How to config u-boot to support 16-bit...
Hong, Hello! This is fine now . Thank you very much for your support! Thank you! Dudechao
View ArticleForum Post: RE: TDA4VM: The device corresponding to serdes cannot be recognized
Hi Takuma, Regarding what Semon said, I misunderstood it. I will go and check the list that was finally presented. Regarding the "reset-gpio" and the 100M clock that you mentioned, we have already...
View ArticleForum Post: RE: TDA4VM: The device corresponding to serdes cannot be recognized
Hi Takuma, Regarding the list of issues you mentioned in the link provided by Semon, it seems that none of them are applicable. I would like to confirm once again whether there is any difference...
View ArticleForum Post: TDA4VEN-Q1: USB0 is unavailable
Part Number: TDA4VEN-Q1 Tool/software: Hi, 1. linux sdk 11 version; 2. Use the evm board to test the usb0, Type-C interface; 3. When a usb2.0 USB flash drive is inserted into type C, The evm board did...
View ArticleForum Post: AM625: AM625: [Security] [Secure Boot] Boot Flow
Part Number: AM625 Tool/software: Just Reading the section of "Secure Booting Sequence" of AM62x from the doc named I got the following questions: Context: using eMMc as a boot-up mode (eMMc as a code...
View ArticleForum Post: AM62P: Whether the AM62P support two indendant dislpay output
Part Number: AM62P Tool/software: Hello Whether the AM62P support two indendant dislpay output? B.R. Changxing DU
View ArticleForum Post: RE: AM62P-Q1: RGMII output clock change to 125MHz failed
Hello Daolin Thanks for your clarification. THe issue has been fixed. Our Link speed is 1000 for the u-boot . The MAC automatcially detect the speed from phy. But the latency is not enabled at PHY side...
View ArticleForum Post: RE: TDA4VH-Q1: OSPI-flash unable to read/write
Hi Kyle & Tanmay, I discovered a strange phenomenon. I upgraded the kernel to the version included in SDK 11.0. However, the newly kernel was unable to recognize the Flash ID. The old kernel(SDK...
View ArticleForum Post: RE: TDA4VM: TDA4VHQ1开发板在使用MCAN模块时，不能进行正常通信
Hi， In standard CAN mode and CANFD mode, communication can only be done when the arbitration segment is 1 Mbps, and setting other values, such as 500kbps, will cause communication failure. The...
View ArticleForum Post: RE: AM6411: Schematic Review for OCP Timing Card Reference Design...
Hello Jennifer Refer below the recommendation for the SGMII interface signals. The schematics layout can be improved for readability. Not sure if the board is for some quick testing where readability...
View ArticleForum Post: AM62P: MAC control Register adddress different between two...
Part Number: AM62P Tool/software: Hello THe MAC control register is different in two version of TRM. Could you please clarify? for version Nov,2024, the following address is : for vrsion Aprial, 2025,...
View ArticleForum Post: RE: AM62P: low probability abnormal thermal reset
Hi Tao and team Anshu has shared on how to disable the VTM by removing from device tree , hopefully that helps We are trying to further understand If the reset occurs if the VTM reset/interrupt is...
View ArticleForum Post: SK-TDA4VM: Getting corrupted stream while streaming AR0234 using...
Part Number: SK-TDA4VM Other Parts Discussed in Thread: TDA4VM Tool/software: Hello, Currently I am enabling AR0234 using FPD link in TDA4VM, Below is my hardware setup. AR0234 ub953 ub960 platform SDK...
View ArticleForum Post: AM6442: IBIS model verification
Part Number: AM6442 Tool/software: Hi, In the AM6442 processor IBIS model, certain pins such as E1 and F1 (clock), E2, T8 (address), and other DDR-related signals, which are expected to be outputs in...
View ArticleForum Post: RE: AM62P-Q1: RGMII output clock change to 125MHz failed
Hello Changxing Du, Thank you. the MAC enables the internal delay on the TX clock. The Rx clock delay is expected to be enabled by the EPHY and good to hear you have been able to configure the dealy...
View ArticleForum Post: RE: [FAQ] AM6442, AM6441, AM6422, AM6421, AM6412, AM6411 and...
Hi Board designers, Refer below E2E for queries related to ethernet interface: (+) AM62P-Q1: RGMII output clock change to 125MHz failed - Processors forum - Processors - TI E2E support forums Thanks...
View ArticleForum Post: RE: CCSTUDIO: How does the new scripting environment in CCS20...
I did some experimentation and have found that the ESM syntax, which uses "module.exports" or "export" to expose shared functions or variables to other source files, and "import" {list} "from" ' ' to...
View Article
