Forum Post: PRU accessing SoC peripherals, - deterministic?
Hi all,I am considering to implement a real time capable driver for external devices within the PRU units. I know that there are dedicated break outs for the PRUs but I require access to the external...
View ArticleForum Post: RE: TMDSDC3359 - DLMS/COSEM demo application capabilities
Can you contact me privately vivek.g@ti.com with your contact details ?-Vivek
View ArticleForum Post: RE: AM335x EVM using the second Ethernet port
Hi Adri,You need to configure the CPSW for Dual EMAC mode. See this wiki: http://processors.wiki.ti.com/index.php/AM335x_CPSW_(Ethernet)_Driver's_Guide#Dual_Standalone_EMAC_mode
View ArticleForum Post: RE: How to remove RTC Alarm from PM Wakeup sources
I downloaded the Cortex-M3 firmware sources, modified them to mask the interrupt, rebuilt the firmware. Made a test, it works! So the RTC alarm irq is somehow really floating when the RTC module is...
View ArticleForum Post: RE: Getting started with TMDSSK3358
Hi Biser,Thanks very much for your prompt reply. Â I did verify that the images on both the Linux and Android SD cards were valid. Â I also double-checked for any stuck buttons but didn't see any. Â I...
View ArticleForum Post: bitbake shows errors when following Sitara Linux Training:...
Hi;we are trying to bring up a custom board with the AM3359 using the latest TI tools. I order to get familiar with the tools we have been running through the TI trainings. Unfortunately when doing the...
View ArticleForum Post: RE: [AM335x] Unable to receive PWM interrupt on PRU
Hi Anil,FYI, there is a new TI released PRU software package: http://www.ti.com/tool/pru-swpkg. The PRU software package includes an example (PRU_IEP) that uses the PRU IEP timer.Note the examples in...
View ArticleForum Post: RE: How to improve the performance of the GPMC interface in burst...
The CS inactive time is about 40 CPU clock cycles, I think this is two long. How can I reduce the active time to improve the speed of transmission?
View ArticleForum Post: RE: [AM335x] EDMA (TC) priority to EMIF
Hi Mukul,Thanks for the confirmation. I understood. If possible, I would like you to raise a request to right person to revise the description in TRM for the next release.Again, thanks for all your...
View ArticleForum Post: RE: am335x ethernet
Hi,The version is ti-sdk-am335x-evm-05.05.00.00.And the version is good.Please tell me how to confiure the am335x.If need to confiure the am335x in NAT mode or other mode
View ArticleForum Post: RE: PRU accessing SoC peripherals, - deterministic?
Hi Thorsten,I will ask the factory team to look at this.
View ArticleForum Post: RE: ethercat_slave FREERUN+DC
Hi Louis,I will ask the factory team to look at this.
View ArticleForum Post: RE: AM335x ISDK EtherCAT full application
Hello Srikant,Thank you for your reply. I select Device1 (EtherCAT) and goto Actions > Select Set/Reset TwinCAT to Config Mode. Then I'm asked about Active Free Run, I select Yes. This put "SSC Box...
View ArticleForum Post: RE: Getting started with TMDSSK3358
A few seconds after you turn on the board you should see display activity. Since you earlier said that there is no enumeration over the USB too, I suspect that there is some malfunction.
View ArticleForum Post: RE: am335x ethernet
This is a very old SDK and it's no longer supported. Have you tried with one of the newer releases (6.0 or 7.0)? This wiki http://processors.wiki.ti.com/index.php/AM335x_CPSW_(Ethernet)_Driver's_Guide...
View ArticleForum Post: RE: Enable uart2 with am335x SDK 7.00 for am335x SK board
Hi Miroslav,the uart2 is ok now.Thanks for your help!Best Regards,Peter
View ArticleForum Post: RE: AM335x GMPC pins Hi-Z
Hi Kazu,For AM335X this is not possible. The GPMC bus state is controlled entirely from the processor. The thing that you can possibly do is have a couple of handshaking signals between the two...
View ArticleForum Post: RE: AM335x eMMC MMC0 boot
Please read section 26.1.7.5.2 of the AM335X Technical Reference Manual Rev. K. Booting from eMMC devices with size 4GB or greater is supported only on MMC1.
View Article