Forum Post: RE: AM335x: Change the pinmux from MMC1 to MMC2
Hi Kato,Yes, your understanding id correct.
View ArticleForum Post: RE: Soft lockup in __getnstimeofday on AM3352
I am sorry, this forum supports only the TI distributed Linux EZSDK. You can try to ask the community at http://beagleboard.org/Community/Forums
View ArticleForum Post: RE: AM3359 GPMC and 8 bit Address operate at 1.8V Question
You can take the worst case values from the AM335X Datasheet Rev. G, Table 5-10. More precise "real world" data is provided here: http://processors.wiki.ti.com/index.php/AM335x_Power_Consumption_Summary
View ArticleForum Post: RE: How long does it take to disable a AM3358 module?
That's understood. Will a module typically disable within, say, a few cycles of the relevant clock or can some modules take a lot longer? Is any data available concerning the enable/disable times of...
View ArticleForum Post: Build Arago with Kernel 3.2?
How can I build arago with linux-am335x-psp?PREFERRED_PROVIDER_virtual/kernel = "linux-am335x-psp" in local.conf is ignored.greetingsHerbert
View ArticleForum Post: RE: AM335x LCD Controller Hsync/Vsync vs DE
Hi Jonathan,[quote user="Jonathan Valdez"]1) From my research on E2E, it appears as if the AM335x controller supports both sync methods (please confirm).[/quote]Yes, the LCD_AC_BIAS_EN signal acts as...
View ArticleForum Post: RE: Build Arago with Kernel 3.2?
Hi Herbert,The easiest way is to download the SDK 6.0 from http://software-dl.ti.com/sitara_linux/esd/AM335xSDK/06_00_00_00/index_FDS.html and follow the instructions on the download page and those...
View ArticleForum Post: RE: Host-only USB1 on AM335x stuck in b-idle
Hi Biser,Thanks for the prompt response and your suggestion.Unfortunately, I cannot change the hardware right now.Like I said, I do have a workaround - the device enumerates everytime if I revert the...
View ArticleForum Post: RE: Disabling TImer5 & 6 in CPSW driver in EZSDK 6.0
Hi Gino,I will ask the factory team about this.
View ArticleForum Post: RE: AM335x: Change the pinmux from MMC1 to MMC2
Sorry, I'm not a Linux expert so I cannot check your DTS. BBB + Angstrom Linux are a community project and they are supported at http://beagleboard.org/Community/Forums
View ArticleForum Post: RE: How long does it take to disable a AM3358 module?
I'm sorry, I don't have precise data about latencies over the AM335X interconnects. On similar processors these latencies vary from 3 to 20 interconnect clock cycles.
View ArticleForum Post: RE: Do i miss anything when try to upload u-boot-spl.bin via ttyUSB1
OK, I understand now. Please tell me is this the Beaglebone White, Beaglebone Black or a custom board? On the Beaglebone White UART0 is routed through an FTDI USB-to-serial converter.
View ArticleForum Post: RE: AM3352, Linux 3.14.19 USB not detecting peripherals
Try 3.16 or better 3.17. There were many fixes/enhancements and look at evmsk DTS as example. You need to activate at least following kernel...
View ArticleForum Post: RE: looking for the pins for uart_echo example
Hey,actually i'm going to develop an interface converter.i get some information from uart and want them to be written to ethercat.do you have something like a starter-guide for devoliping?kind regards
View ArticleForum Post: RE: Question about AM437x PRU pin mux
Hi Biser,Thank you for the reply.I uderstood.best regards,g.f.
View ArticleForum Post: RE: AM3359 / PROFINET
Many thanks for your reply! I will do request on Molex.
View ArticleForum Post: RE: NDK/NSP for AM3359 ICE v1
Hi Timo,I'm not an expert on the ISDK, but this could be a good starting point: http://processors.wiki.ti.com/index.php/AM335x_SYSBIOS_Industrial_SDK_Getting_Started_Guide You can try searching the...
View ArticleForum Post: RE: CPU idle and PM firmware on AM3352 / random slowdown
For the Linux-3.12.11-rt17, can you post where you got the kernel from, any patches, and where the rt patch came from?Steve K.
View Article