Forum Post: RE: eth0 interferes eth1 in dual mac config
Hi BiserThe two ports are assigned to 192.168.201.174 and 192.168.202.174 respectively. Linux kernel version is 3.12. BRCheng Shi
View ArticleForum Post: How to keep u-boot splash display during kernel booting
Hi, AllSplash display is required to keep turning on during kernel booting until user application running. But clocks are stopped when kernel start up, and display timing is resumed with tilcdc driver...
View ArticleForum Post: RE: Cannot boot from Starterware for AM335x Starter Kit
There is a dedicated forum for Starterware: http://e2e.ti.com/support/embedded/starterware/default.aspx. Please post your Starterware related questions there. This forum supports only the TI...
View ArticleForum Post: RE: How to keep u-boot splash display during kernel booting
You will need to modify the kernel initialization in order to do this. Another approach can be to modify u-boot, disabling console output and u-boot prompt timeout. Then you can put on your splash...
View ArticleForum Post: RE: Ethernet problem on Starter Kit
Hi Will,You may want to look up the differences between the two U-Boot versions here: http://git.denx.de/?p=u-boot.git;a=tagsBest regards,Miroslav
View ArticleForum Post: RE: About AM335x DM Timer
Dear Sir,I am using Beaglebone and running TI SDK for beaglebone.I want to configure a software time interrupt at every 3 sec in beaglebone. For this purpose i had written a kernel module and checking...
View ArticleForum Post: RE: “WARNING: Caches not enabled” on AM335x u-boot
I meet the question also,and I found it maybe contact with a function enable_caches(),which was called in board_init_r in arch/arm/lib/board.c ,but I can't found which it's defined,do you already make...
View ArticleForum Post: RE: AM335x Starter Kit Capacitive Touch Screen
If you have replaced the new tslib (libs+programs) and you still get zeroes, there is still something wrong with the communication between tslib and driver. find out how the driver reports the touch...
View ArticleForum Post: RE: ADC on SITARA
If you don't have this file in the SDK provided by Silica, then most probably the SDK has been modified to use another board file and the am335x_evm_defconfig won't work for your board.Please ask...
View ArticleForum Post: RE: Actual GPMC XIP Timing on EVM is different from TRM.
Looking at this again it seems to me that the 50MHz frequency mentioned in the note below the table is wrong - should be 100MHz, resp. 10ns.
View ArticleForum Post: RE: I2C1(/dev/i2c-2) not working on AM335x for D15 and D16...
Can you post the results of the cat command?
View ArticleForum Post: RE: ICE v2 + lwip + enetlwip sample not working ?
Romain,There could be many reasons for failure of netif_add, but it is usually because MDIO Alive/Link register for the particular port is not set. Are the Ethernet LEDs showing correct behavior on...
View ArticleForum Post: RE: AM3352 RMII ethernet: no data sent or received
Re-reading this, I realized I'd been unclear. When I said that the omap_hwmod_lookup caused the whole thing to exit without registering the devices, that is NEW behavior that only happens after...
View ArticleForum Post: RE: AM3703 USB Testmode
The procfs entry for test_packet is only available in the TI SDK 2.6.37 kernel, not in other kernels you got from kernel.org or anywhere else.The debugfs entry for test_packet in any kernel is...
View ArticleForum Post: RE: AM335x: CAN Interface 2 - no valid message number set in the...
Klaus,1. Can you define what exactly happens during this powerfail? Is this an entire board power failure, etc2. What happens immediately after this powerfail? Does the board automatically recover and...
View ArticleForum Post: RE: TMDSICE3359 some general Questions
One possible solution is to use AM335x IDK board that comes with EtherCAT and a standard Ethernet port and you will need to add, by yourself, the Ethernet software, because our IDK SW does not support it.
View ArticleForum Post: RE: AM335x and RMII TLK105, link not stable
Paul,OK, I understand now that the pin is used to route the clock internally at the same time as driving the external circuit. So is the demo board file wrong then? It does not have bit 5 set.Even...
View ArticleForum Post: Getting AM3517 to wakeup from GPIO source
Hello, it seems like I am going round in circles trying to get my system to be able to suspend to memory and then wakeup via a GPIO event.I have configured my system to use GPIO_28 as the wakeup source...
View ArticleForum Post: RE: AM3517 gpio wakeup enable
Hello MatteoI know I am reviving an old post but did you manage to solve your issue ?I am trying to do the same with an AM3517 but using GPIO_28.Kind RegardsMarc
View Article