Forum Post: RE: I2S
Siddharth, unfortunately the StarterWare package doesn't support your device, but you may check the drivers inside and perhaps reuse them for your bare-bones code.Best regards,Miroslav
View ArticleForum Post: RE: Disable partilcular gpio interrupt to wake system from low...
Any update ?Shabbir Limdiwala
View ArticleForum Post: RE: How to configure frame-rate of video display in AM3505 DSS?
Hi Miroslav,We tried with fbset utility but we couldn't get any option to change frame rate.Can you please explain how can i control frame rate by using fbset.Which are the parameters i have to...
View ArticleForum Post: RE: TPS65217 with 12V Supply
Hi Byron,Our hardware engineer is currently on vacation and I'll forward your question to the factory team.Best regards,Miroslav
View ArticleForum Post: RE: am335x starter kit. status check.
Kenneth, I'll try to involve someone from the factory team regarding your issue.Best regards,Miroslav
View ArticleForum Post: RE: Reg.RTC mechanism in AM3359
Hi Ibram,Since our hardware engineer is out of office, I'll forward your question to the factory team.Best regards,Miroslav
View ArticleForum Post: RE: How to assign different IP address to AM335X 2 cpsw ethernet...
Hi Rolan,As Vinesh mentioned, you have to use a combination of the configuration file (*.cfg) and C code to do this.Please refer to the following post which provides these...
View ArticleForum Post: Configuring the Noise Filter in the preview engine in the AM3703
HI,We are using the AM3703 Preview engine to convert the raw bayer image to YUV. After converting we could see more noise in the output. We tried to used the Noise filter of the preview engine with the...
View ArticleForum Post: RE: Problem with Signal On Power Rails: AM3354 and TPS65217
hi Paul, the frequency actually seems to drift somewhat between 27 and 30 mHz. I'm only trying to indicate that it is way below the fundamental switching frequency of the PMIC. It would be nice to post...
View ArticleForum Post: Processor Hangs in SPL or U-Boot
I've got a BeagleBone White that has suddenly stopped booting up after we tried to make a board change to disable the RTC clock. The symptom is the power LED comes on and I get one line of text out the...
View ArticleForum Post: RE: Getting Touchscreen working on Beaglebone Black
And at the bottom of the Platform data section there is a link to the source code, that when followed takes you to a git repository for kernel 3.2, not the 3.12 that is distributed with the 7.0.0.0...
View ArticleForum Post: RE: Ethernet to FieldBus Bridge
I preface this post with a warning -- there a a lot of question in this post.okay, thanks. That is helpful. I have a feeling that once i finish theSercos III to Ethernet bridge many other interfaces...
View ArticleForum Post: RE: AM335x RGMII Problem (PHY KSZ9021RL): ping fails
Could you provide the contents of the relevant AM335x CPSW_SL_MACCTRL and CPSW_STATS registers while the device is attempting PING?
View ArticleForum Post: RE: AM335x GPMC CLK free running possible?
[quote user="J Burke"]Basically, is there any way to get a usable free running clock in the MHz range on an output pin AM335x?[/quote]Can you use a timer / PWM pin for your application? They work.
View ArticleForum Post: RE: how to enable ip over usb on ti-sdk-am335x-evm-06.00.00.00
Pat,I'm glad your issue is resolved, and thanks so much for posting your solution. This information is extremely valuable for those that may run into the same issue you did in the future.
View ArticleForum Post: RE: Babble error in AM3352
Hi,It is a GSM modem.Regards,Yashavadan Dalsaniya
View ArticleForum Post: RE: am335x custom board display selection
Well, all these are software settable values and depent on what you are using (Linux, barebone, etc).If Linux, the like parameters might be read by the driver from your eeprom.Also many display...
View ArticleForum Post: AM335x i2c problem
Hi, everyone my platform AM3352, BSP SDK 6.0, I want to add device under I2C bus, Modify linux/arch/arm/mach-omap2/board-am335xevm.c static struct i2c_board_info __initdata am335x_i2c0_boardinfo[] =...
View ArticleForum Post: Swapping bit pattern in 18 bit LCD running on Andorid
Hello.I am working on custom board that has 18 bit LCD connection interface. Android is running on the board.There are four columns in given below table. Column no 1 and 2 shows the standard...
View ArticleForum Post: DDR2 not operation on custom AM3352 board
Hello,ProblemI am having issues getting DDR2 to talk on custom board using AM3352. The values cannot be read from DDR2. If I try to write to in the memory window of CCS, zeros are always...
View Article