Forum Post: RE: U-Boot SPL Stuck
Victor,All the best with x-ray. Make sure your PLL supplies are fine. If you dont see ddr clk in few more boards, I would think its not solder issue. If you have clkout, probe that to make sure your...
View ArticleForum Post: RE: Am335 CDC NCM gadget issue With DMA
Hi,We are using ti-sdk-am335x-evm-05.05.01.00 SDK, it is an ETAB based version. Can i get the patch for this fix ?
View ArticleForum Post: RE: AM335x I2C0 - AERR set after ITC_EN=1
Hi John, If this is baremetal programming I would suggest that you use the Starterware package as a reference.
View ArticleForum Post: RE: AM335xsk starter kit not boot from the SD card
Can you verify the downloaded files against the md5 sums provided on the download page?Can you post the output during the creation of the SD card? I just tried reformatting an SD card using the...
View ArticleForum Post: RE: MLO with Craneboard and Buildroot
Ratnesh, this forum supports only the TI distributed Linux EZSDK. Please direct your questions to http://designsomething.org/craneboard/w/overview/default.aspx/.Best regards,Miroslav
View ArticleForum Post: RE: AM335x 300MHz : PLL configuration in ROM boot loader
Hi James-san,I have the same question.The ROM bootloader configures the MPU clock to 500MHz for all devices so that the section 26.1.4.3 in TRM describes it.Is it allowed to operate the 300MHz devices...
View ArticleForum Post: RE: (AM335X) UBOOT CRASH WHEN CANNEL EEPROM
Please see this post: http://e2e.ti.com/support/arm/sitara_arm/f/791/t/297989.aspx
View ArticleForum Post: RE: Problem accessing I2C from userspace (EREMOTEIO)
Hi Benjamin,I've escalated this to the factory team.Best regards,Miroslav
View ArticleForum Post: RE: How to switch on/off bluetooth from host machine or through c...
Hi Harsha,If you are using wl1271, please take a look at this wiki page. There are command line demo scripts located in /usr/share/wl1271-demos/bluetooth/scripts/ on your device.Best regards,Miroslav
View ArticleForum Post: RE: Cross Compile any package [ CGMINER 3.1.1] on texas...
Hi,The am335x cross-compile toolchain is located in <SDK_dir>/linux-devkit/sysroots/i686-arago-linux/usr/bin/. The CC prefix is "arm-linux-gnueabihf-".Read the README file that comes with the...
View ArticleForum Post: RE: AM335x U-boot pin mux problem
Thanks, I've used the same settings in u-boot and Linux./debug/omap_mux # cat i2c0_sclname: i2c0_scl.i2c0_scl (0x44e1098c/0x98c = 0x0070), b NA, t NAmode: OMAP_MUX_MODE0 | AM33XX_PIN_INPUT_PULLUP |...
View ArticleForum Post: RE: Turning on the User LEDs on the AM335x EVM
Here's a related thread that you might find useful:http://e2e.ti.com/support/arm/sitara_arm/f/791/t/223896.aspx
View ArticleForum Post: RE: AM335x EVM RTC
Which EVM are you using?For Starterware please direct your questions to the dedicated forum: http://e2e.ti.com/support/embedded/starterware/default.aspx
View ArticleForum Post: RE: AM335x StartKit / SDK for BT audio
Hi Bob, The AM335X Starter Kit does have BT Audio wired to McASP0. This is the product page: http://www.ti.com/tool/tmdssk3358. About your second question I can't say - maybe you could ask this on the...
View ArticleForum Post: RE: [ICE DEMO BOARD] Ethercat LED's U29 fet buffer
The AM335X TRM Rev. J states in Table 26-7 that SYSBOOT[12] must be low for this boot setting. This is required for proper booting.
View ArticleForum Post: RE: AM335xsk starter kit not boot from the SD card
Hi Santosh,The script name is mkmmc-android.sh, not mkmmc-android.Best regards,Miroslav
View ArticleForum Post: RE: AM335x with TPS65910AA1SRL hang
Is this before or after you try to start the board? Can you tell me the expected startup behaviour - by applying +5V or by pushbutton?
View ArticleForum Post: RE: Read smartreflex values and failed sr_init
You are using a 600MHz processor that supports only OPP100 and OPP50. Registers for OPP120 and OPP Turbo should be empty. What is your PMIC? Do you have I2C0 connected to it? See this link:...
View Article