Processors

Our customer tries the loopback test via a switching hub for one ethernet port. The hub has the port mirroring feature.They want to confirm that a test frame with the source/destination MAC address of...

View Article

Forum Post: RE: AM335X 10MB/s ethernet issues

October 6, 2014, 3:55 pm

I tried the same test using two linux PC and got even worse results at 10Mbps. I will try the same test again perhaps using a different router tomorrow.

View Article

Forum Post: RE: using only port0 for ethercat on sitara

October 6, 2014, 6:51 pm

Hi,[quote user="Mario Giovanni Casali"]Your link is ok and I already downloaded both sdk 1.1.0.5 and bios 6.40.03.39 and xdc_tools 3.30.04.52 cores (what's the right one for CCSV6 under Windows? with...

View Article

Forum Post: RE: Can the AM3352 core support 16X16bit GPMC burst mode?

October 6, 2014, 7:30 pm

Yes. Note you'll need to use EDMA to succeed in generating bursts that large. See this thread for more explanation why:http://e2e.ti.com/support/dsp/omap_applications_processors/f/447/t/43106.aspx

View Article

Forum Post: RE: SysBoot Configuration pin for AM3352

October 6, 2014, 11:09 pm

Hi,See this wiki: http://processors.wiki.ti.com/index.php/Sitara_Uniflash_Quick_Start_Guide#Overview :"Uniflash is one part of an overall system that includes the Windows PC on which Uniflash runs, a...

View Article

Forum Post: RE: AM335x USB Host problems in DMA mode

October 6, 2014, 11:11 pm

Hi Dave,I will bring this to the attention of the factory team. Answer will be posted on this thread.

View Article

Forum Post: RE: u-boot compilation does not show commands

October 6, 2014, 11:28 pm

Hi Daniel,The command line:make ARCH=arm CROSS_COMPILE=/home/USER/ti-sdk-am335x-evm-06.00.00.00/linux-devkit/sysroots/i686-arago-linux/usr/bin/arm-linux-gnueabihf- am335x_evmThis should generate all...

View Article

Forum Post: RE: Installing udev-182 on am335x

October 6, 2014, 11:30 pm

Hi Michael,I will try to escalate this to the factory team, but I'm afraid it will go back to the WiLink people. Anyway, let's see if there will be some feedback.

View Article

Forum Post: RE: TMDSSK3358: Evaluate the CAN interface

October 7, 2014, 12:32 am

Hi Kato,The GP EVM is the only possibility for evaluating CAN. There are no CAN-related errata on the AM335X Rev.1.0.

View Article

Forum Post: RE: AM335x McASP sync to systick / PTPv2 local clock

October 7, 2014, 12:41 am

Hi Vincent,No feedback so far, I have renewed the request.

View Article

Forum Post: RE: booting a custom am335x board

October 7, 2014, 1:37 am

Check this link too: http://processors.wiki.ti.com/index.php/Linux_Core_U-Boot_User's_Guide

View Article

Forum Post: RE: Custom our board based on AM335x starter kit

October 7, 2014, 1:53 am

Sorry, I am not a Linux expert. These are DTS files I think. Check the documentation within the SDK.

View Article

Forum Post: RE: am335x boot from NAND Spansion S34ML01G1

October 7, 2014, 1:54 am

More practically:1st we have to check if the NAND is at all recognized by the RBL and if NAND boot starts at all.- How do the NAND and GPMC timings look like compared to what is documented at page 4684...

View Article

Forum Post: RE: AM437x gp evm - emmc boot - raw or card

October 7, 2014, 1:59 am

Sorry i ve to revert the fact that the system is stuck .. it actually is not stuck and does try the mmc0 after "failing" to boot the emmc on mmc1so i am back to the drawing board and the scope again...

View Article

Forum Post: RE: CDC NCM throughput on Beaglebone

October 7, 2014, 4:58 am

Here is a related post: http://e2e.ti.com/support/arm/sitara_arm/f/791/t/318381.aspx

View Article

Forum Post: RE: Profinet PRU support

October 7, 2014, 5:22 am

Hi Jonathan,If you are programming the host MAC address correctly as suggested by Frank above then a unicast frame should be received. "PN_Receive_Decision_Table" is used only for multicast...

View Article