Thanks for your interest. We attached kernel boot log and insmod output. 1.-------------------------------------- kernel boot log -------------------------------------- [ 1.551317] mmc0: host does not support reading read-only switch, assuming write-enable [ 1.561437] mmc0: new high speed SDHC card at address 59b4 [ 1.567886] mmcblk0: mmc0:59b4 SD 14.7 GiB [ 1.575150] mmcblk0: p1 p2 [ 1.655774] input: gpio_buttons0 as /devices/platform/gpio_buttons0/input/input0 [ 1.667161] hctosys: unable to open rtc device (rtc0) [ 1.673134] lis3_reg: disabling [ 1.676671] ALSA device list: [ 1.679779] No soundcards found. [ 1.744338] mmc1: error -110 whilst initialising MMC card [ 2.562209] EXT4-fs (mmcblk0p2): recovery complete [ 2.569969] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.578320] VFS: Mounted root (ext4 filesystem) on device 179:2. [ 2.589095] devtmpfs: mounted [ 2.596533] Freeing unused kernel memory: 1024K [ 2.873218] systemd[1]: System time before build time, advancing clock. [ 2.926879] systemd[1]: systemd 230 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN) [ 2.946043] systemd[1]: Detected architecture arm. Welcome to Arago 2017.10! [ 2.986112] systemd[1]: Set hostname to . [ 3.308580] systemd[1]: [/lib/systemd/system/gadget-init.service:15] Unknown lvalue 'ExecStopPre' in section 'Service' [ 3.594870] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe. [ OK ] Listening on /dev/initctl Compatibility Named Pipe. [ 3.636545] systemd[1]: Created slice System Slice. [ OK ] Created slice System Slice. [ 3.664548] systemd[1]: Listening on udev Kernel Socket. [ OK ] Listening on udev Kernel Socket. [ 3.695320] systemd[1]: Created slice User and Session Slice. [ OK ] Created slice User and Session Slice. [ 3.724563] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ OK ] Started Forward Password Requests to Wall Directory Watch. [ 3.813124] systemd[1]: Reached target Swap. [ OK ] Reached target Swap. [ OK ] Created slice system-getty.slice. [ OK ] Listening on udev Control Socket. [ OK ] Listening on Syslog Socket. [ OK ] Listening on Process Core Dump Socket. [ OK ] Reached target Slices. [ OK ] Started Dispatch Password Requests to Console Directory Watch. [ OK ] Reached target Remote File Systems. [ OK ] Listening on Network Service Netlink Socket. [ OK ] Created slice system-serial\x2dgetty.slice. [ OK ] Listening on Journal Socket. Starting Remount Root and Kernel File Systems... Starting alignment.service... Mounting Debug File System... [ 4.327961] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) Mounting POSIX Message Queue File System... Starting Load Kernel Modules... Starting Create Static Device Nodes in /dev... Starting Setup Virtual Console... [ OK ] Listening on Journal Socket (/dev/log). [ 4.551217] cryptodev: loading out-of-tree module taints kernel. [ 4.577528] cryptodev: driver 1.8 loaded. Starting Journal Service... [ OK ] Reached target Paths. Mounting Temporary Directory... [ OK ] Mounted Debug File System. [ OK ] Mounted POSIX Message Queue File System. [ OK ] Mounted Temporary Directory. [ OK ] Started Journal Service. [ OK ] Started Remount Root and Kernel File Systems. [ OK ] Started alignment.service. [ OK ] Started Load Kernel Modules. [ OK ] Started Create Static Device Nodes in /dev. [ OK ] Started Setup Virtual Console. Starting udev Kernel Device Manager... Mounting Configuration File System... Starting Apply Kernel Variables... Starting udev Coldplug all Devices... [ OK ] Reached target Local File Systems (Pre). Mounting /media/ram... Mounting /var/volatile... Starting Flush Journal to Persistent Storage... [ OK ] Mounted Configuration File System. [ OK ] Mounted /var/volatile. [ OK ] Mounted /media/ram. [ OK ] Started udev Kernel Device Manager. [ OK ] Started Apply Kernel Variables. [ 5.700149] systemd-journald[101]: Received request to flush runtime journal from PID 1 Starting Load/Save Random Seed... [ OK ] Reached target Local File Systems. [ OK ] Started Flush Journal to Persistent Storage. [ OK ] Started Load/Save Random Seed. Starting Create Volatile Files and Directories... [ OK ] Started Create Volatile Files and Directories. Starting Network Time Synchronization... Starting Update UTMP about System Boot/Shutdown... [ OK ] Started Update UTMP about System Boot/Shutdown. [ OK ] Started Network Time Synchronization. [ OK ] Reached target System Time Synchronized. [ OK ] Created slice system-systemd\x2dbacklight.slice. Starting Load/Save Screen Backlight...htness of backlight:backlight... [ 7.244965] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ OK ] Found device /dev/ttyS0. [ 7.350837] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0 [ OK ] Started udev Coldplug all Devices. [ OK ] Started Load/Save Screen Backlight Brightness of backlight:backlight. [ OK ] Reached target System Initialization. [ OK ] Listening on RPCbind Server Activation Socket. [ OK ] Listening on dropbear.socket. [ OK ] Listening on D-Bus System Message Bus Socket. [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. [ OK ] Reached target Sockets. [ OK ] Reached target Basic System. [ OK ] Started Kernel Logging Service. [ OK ] Started D-Bus System Message Bus. [ 8.237175] omap_hwmod: pruss: _wait_target_ready failed: -16 [ 8.242987] pruss-soc-bus 4a326000.pruss-soc-bus: use pm_runtime_put_sync_suspend() in driver? [ 8.430521] pruss-soc-bus 4a326000.pruss-soc-bus: couldn't enable module [ 8.505963] pruss-soc-bus: probe of 4a326000.pruss-soc-bus failed with error -16 [ 8.574523] omap-sham 53100000.sham: hw accel on OMAP rev 4.3 [ 8.605528] remoteproc remoteproc0: wkup_m3 is available [ 8.695118] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2 Starting Network Service... [ 8.739715] omap-aes 53500000.aes: will run requests pump with realtime priority Starting Telephony service... [ 8.901514] remoteproc remoteproc0: powering up wkup_m3 [ 8.943103] omap_hwmod: gfx: failed to hardreset [ 8.958688] PM: Cannot get wkup_m3_ipc handle [ 9.166257] pvrsrvkm 56000000.sgx: Unable to reset SGX! [ 9.186810] omap_hwmod: gfx: _wait_target_ready failed: -16 [ 9.232743] pvrsrvkm 56000000.sgx: use pm_runtime_put_sync_suspend() in driver? [ 9.232768] PVR_K:(Error): EnableSGXClocks: pm_runtime_get_sync failed (16) [ 9.232781] PVR_K:(Error): SysInitialise: Failed to Enable system clocks (175) [ 9.319911] asoc-simple-card sound: tlv320aic3x-hifi 4803c000.mcasp mapping ok [ 9.361612] PM: Cannot get wkup_m3_ipc handle [ 9.626100] Bluetooth: Core ver 2.22 [ 9.626187] NET: Registered protocol family 31 [ 9.626191] Bluetooth: HCI device and connection manager initialized [ 9.626213] Bluetooth: HCI socket layer initialized [ 9.626224] Bluetooth: L2CAP socket layer initialized [ 9.626254] Bluetooth: SCO socket layer initialized [ 9.664968] net eth1: initializing cpsw version 1.12 (0) [ 9.664980] cpsw 4a100000.ethernet: initialized cpsw ale version 1.4 [ 9.664985] cpsw 4a100000.ethernet: ALE Table size 1024 [ 9.858477] SMSC LAN8710/LAN8720 4a101000.mdio:01: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:01, irq=-1) [ 9.872886] cpts ptp bc clkid 0 [ 9.896799] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 10.035288] net eth0: initializing cpsw version 1.12 (0) [ 10.134719] SMSC LAN8710/LAN8720 4a101000.mdio:00: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=4a101000.mdio:00, irq=-1) [ 10.139071] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 11.327389] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. Starting Print notice about GPLv3 packages... [ 11.589208] remoteproc remoteproc0: Booting fw image am335x-pm-firmware.elf, size 224268 Starting Save/Restore Sound Card State... Starting Login Service... [ 11.722649] remoteproc remoteproc0: remote processor wkup_m3 is now up [ 11.722673] wkup_m3_ipc 44e11324.wkup_m3_ipc: CM3 Firmware Version = 0x192 Starting Avahi mDNS/DNS-SD Stack... [ OK ] Started Daily Cleanup of Temporary Directories. [ OK ] Reached target Timers. Starting uim-sysfs.service... [ OK ] Started System Logging Service. [ 12.244761] cpsw 4a100000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ OK ] Started Network Service. [ 12.372425] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ OK ] Started Save/Restore Sound Card State. [ OK ] Found device /dev/ttyS3. [ OK ] Found device /dev/mmcblk0p1. [ OK ] Started Telephony service. [ OK ] Started Avahi mDNS/DNS-SD Stack. [ OK ] Started Login Service. Starting Start USB gadget... [ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch. [ OK ] Reached target Network. [ OK ] Started strongSwan IPsec IKEv1/IKEv2 daemon using ipsec.conf. Starting Simple Network Management Protocol (SNMP) Daemon.... Starting Permit User Sessions... Starting Enable and configure wl18xx bluetooth stack... Starting Lightning Fast Webserver With Light System Requirements... Starting Network Name Resolution... [ 14.343455] udc-core: couldn't find an available UDC - added [g_multi] to list of pending drivers [ OK ] Started Permit User Sessions. [ OK ] Started Lightning Fast Webserver With Light System Requirements. [ OK ] Started Getty on tty1. [ OK ] Started Serial Getty on ttyS3. [ OK ] Started Serial Getty on ttyS0. [ OK ] Started Network Name Resolution. [ 15.247133] NET: Registered protocol family 15 [ 15.859882] TI-am335x-tsc TI-am335x-tsc: ti,charge-delay not specified [ 16.000072] input: ti-tsc as /devices/platform/ocp/44e0d000.tscadc/TI-am335x-tsc/input/input1 [ 16.140849] PM: bootloader does not support rtc-only! [FAILED] Failed to start Start USB gadget. See 'systemctl status gadget-init.service' for details. [ OK ] Started Enable and configure wl18xx bluetooth stack. [ 16.548451] Initializing XFRM netlink socket [ 16.976720] random: crng init done [ OK ] Started Simple Network Management Protocol (SNMP) Daemon.. [ 17.753717] 47401300.usb-phy supply vcc not found, using dummy regulator [ 17.872858] 47401b00.usb-phy supply vcc not found, using dummy regulator [ 17.882392] usbcore: registered new interface driver usbfs [ 17.882459] usbcore: registered new interface driver hub [ 17.882589] usbcore: registered new device driver usb [ 18.247635] musb-hdrc musb-hdrc.0: MUSB HDRC host driver [ 18.364159] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 1 [ 18.469737] hub 1-0:1.0: USB hub found [ 18.526558] hub 1-0:1.0: 1 port detected [ 18.677875] using random self ethernet address [ 18.682367] using random host ethernet address [ 18.764074] using host ethernet address: A8:1B:6A:33:52:E8[ 18.769482] using random self ethernet address [ 18.908216] using random host ethernet address [ 18.959553] using host ethernet address: A8:1B:6A:33:52:E8[ 19.017476] usb0: HOST MAC a8:1b:6a:33:52:e8 [ 19.051586] usb0: MAC ee:ba:77:e1:d8:e2 [ 19.180081] Mass Storage Function, version: 2009/09/11 [ 19.205192] LUN: removable file: (no medium) [ 19.234972] LUN: removable read only file: /dev/mmcblk0p1 [ 19.281358] Number of LUNs=1 [ 19.310353] g_multi gadget: Multifunction Composite Gadget [ 19.348559] g_multi gadget: g_multi ready [ 19.410258] musb-hdrc musb-hdrc.1: MUSB HDRC host driver [ 19.490409] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 2 [ 19.563197] hub 2-0:1.0: USB hub found [ 19.595433] hub 2-0:1.0: 1 port detected [ 19.606536] g_multi gadget: high-speed config #1: Multifunction with RNDIS _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am335x-evm ttyS0 Arago 2017.10 am335x-evm ttyS0 am335x-evm login: *************************************************************** *************************************************************** NOTICE: This file system contains the following GPLv3 packages: autoconf binutils cifs-utils cpp-symlinks cpp dosfstools g++-symlinks g++ gawk-dev gawk gcc-symlinks gcc gdb gdbserver glmark2 gstreamer1.0-libav hidapi libcairo-perf-utils libgmp10 libidn11 libmpc3 libmpfr4 libreadline-dev libreadline6 m4-dev m4 make nettle swig-dev swig If you do not wish to distribute GPLv3 components please remove the above packages prior to distribution. This can be done using the opkg remove command. i.e.: opkg remove Where is the name printed in the list above NOTE: If the package is a dependency of another package you will be notified of the dependent packages. You should use the --force-removal-of-dependent-packages option to also remove the dependent packages as well *************************************************************** *************************************************************** [ 26.145032] hrtimer: interrupt took 182500 ns _____ _____ _ _ | _ |___ ___ ___ ___ | _ |___ ___ |_|___ ___| |_ | | _| .'| . | . | | __| _| . | | | -_| _| _| |__|__|_| |__,|_ |___| |__| |_| |___|_| |___|___|_| |___| |___| Arago Project http://arago-project.org am335x-evm ttyS0 Arago 2017.10 am335x-evm ttyS0 am335x-evm login: 2.-------------------------------------- lsmod command output -------------------------------------- root@am335x-evm:~# lsmod Module Size Used by usb_f_acm 5276 1 u_serial 11171 3 usb_f_acm sha512_generic 9967 0 usb_f_ecm 6492 1 sha512_arm 12252 0 sha256_generic 10178 0 sha1_generic 2864 0 sha1_arm_neon 6261 0 sha1_arm 3862 1 sha1_arm_neon md5 2219 0 musb_dsps 9734 0 musb_hdrc 87874 1 musb_dsps usbcore 201869 1 musb_hdrc phy_am335x 2372 2 phy_am335x_control 2937 1 phy_am335x phy_generic 5372 1 phy_am335x des_generic 17608 0 cbc 2388 0 xfrm_user 22370 2 xfrm4_tunnel 2040 0 ipcomp 2257 0 xfrm_ipcomp 4311 1 ipcomp ti_am335x_tsc 6029 0 esp4 6402 0 ah4 5627 0 af_key 27032 0 xfrm_algo 6989 5 xfrm_user,esp4,ah4,af_key,xfrm_ipcomp g_multi 6145 0 usb_f_mass_storage 37218 2 g_multi usb_f_rndis 15482 2 g_multi u_ether 13001 3 usb_f_ecm,g_multi,usb_f_rndis libcomposite 44446 5 usb_f_ecm,usb_f_acm,usb_f_mass_storage,g_multi,usb_f_rndis udc_core 19450 8 usb_f_ecm,usb_f_acm,usb_f_mass_storage,u_serial,musb_hdrc,u_ether,usb_f_rndis,libcomposite usb_common 4737 6 phy_am335x,udc_core,musb_hdrc,libcomposite,musb_dsps,usbcore bluetooth 337541 2 snd_soc_simple_card 5844 0 snd_soc_simple_card_utils 5095 1 snd_soc_simple_card pm33xx 6433 0 wkup_m3_ipc 8240 1 pm33xx wkup_m3_rproc 3670 1 remoteproc 28645 2 wkup_m3_rproc,wkup_m3_ipc pvrsrvkm 403500 0 omap_aes_driver 19334 0 crypto _engine 7098 1 omap_aes_driver omap_sham 21950 0 ti_emif_sram 5663 1 pm33xx pruss_soc_bus 4105 0 snd_soc_tlv320aic3x 48423 1 musb_am335x 1426 0 rtc_omap 9662 1 omap_wdt 4634 0 ti_am335x_tscadc 6290 1 ti_am335x_tsc sch_fq_codel 9115 4 uio_module_drv 7251 0 uio 9121 1 uio_module_drv cryptodev 38083 1 I would appreciate your advice.
↧